Craftsman 10'' Single Bevel Sliding Compound Miter Saw (21237)
Item# 00921237000 | Model# 21237Specifications & Dimensions
| Dimensions: | |
|---|---|
| Table Dimensions (LxW): | 18-1/8 x 13-3/4 in. |
| Product Overview: | |
| Crosscut Capacity - 0 Miter 0 Bevel: | 4in x 12in |
| Crosscut Capacity - 0 Miter 45 Left Bevel: | 2in x 12in |
| Crosscut Capacity - 0 Miter 45 Right Bevel: | 2in x 12in |
| Crosscut Capacity - 45 Miter 0 Bevel: | 4in x 8in |
| Crosscut Capacity - 45 Miter 45 Left Bevel: | 2in x 8in |
| Crosscut Capacity - 45 Miter 45 Right Bevel: | 2in x 8in |
| CSA Listed: | Yes |
| Fence Type: | Fixed |
| Item Weight (lbs.): | 52.9 lbs. |
| Package Contents: | Table Extension, Stop Block, Clamp(s), Dust Bag |
| Quick Release Vise: | Yes |
| Spindle Lock: | Yes |
| Type: | Sliding compound miter |
| Warranty Detail Link: | craftsman warranty |
| Cord: | |
| Cord Length (ft.): | 6 |
| Cord Management: | Manual Wrap |
| Blade: | |
| Diameter (In): | 10 in. |
| Motor-Engine: | |
| Amps: | 15.0 |
| Motor Brushes: | Consumer replaceable |
| Motor Voltage: | 120 |
| RPM: | 4800 |
| Guides & Instructions: | |
| Owner's Manual: | Yes |
| General Features: | |
| Arbor Size: | 5/8 in. |
| Compound Miter: | Yes |
| Detent Base: | Yes |
| Miter Index: | 0-45 deg. left/right |
| Cutting Tool: | |
| Align-a-Cut: | No |
| Cut Depth At 90 Degrees: | 4 in. |
| Miter Detents: | 0, 15, 22-1/2, 31.6 and 45 deg. left/right |
| Materials: | |
| Table Material: | Aluminum |
| Installation: | |
| Assembly Required: | Assembly Required |
Overview
Ratings & Reviews
Special
Projects
Product Description
A Craftsman 10' Sliding Compound Miter Saw Gets the Job Done Precisely Right
Smooth cutting with laser guided precision, lightweight, portable and slicing seamlessly through thick materials, the Craftsman 10' single bevel sliding compound miter saw is the perfect addition to a jobsite and home shop alike. Spinning at 4,800 revolutions per minute, no matter which blade you slip onto the collar of this compound, you'll cut through wood both hard and soft, leaving sharp edges and tight corners with every cut.
The perfect way to save money on any job, the Craftsman 10' sliding compound miter saw uses smaller, easy-to-maintain blades than larger models, but this saw still delivers the reach to spin through boards up to 12 inches wide. Perfect for quick work, this saw features a Laser Trac that clearly lines up with your pencil marks for fast work and when you're looking to cut precision miters, the built-in clamping system gives you that exact angle every time. The Craftsman 10" compound miter saw delivers precision and versatility that you can count on.
- The Craftsman 10' sliding compound miter saw features a 15.0 Amp motor that delivers high torque and speed
- Include compound miter saw, blade, dust bag, blade wrench, clamp and extensions
- Studs, joists and posts cut easily with the dual slide bearing rail system
- Telescoping aluminum extensions with stop block provide additional support for longer work pieces
- Laser Trac not only gives you an accurate cut line, but doesn't ever run out of batteries
- The 0-50 degree miter adjustment includes common positive stops for accurate cuts on the fly
- 60 carbide teeth give the 10-inch saw blade more life and bite than others
- Aluminum construction is durable and easy to move from home to jobsite
- Some assembly required
- Comes with Owner's Manual (English)
Added on February 16, 2009
Overall, others give this:
Reviewers may have received a benefit, like a sweepstakes entry or rewards program points, in exchange for writing a review.
Those benefits were not conditioned on the positive or negative content of the review.
Most Helpful Reviews
Madison, AL
via sears.com
I bought this to replace an older miter saw. This has the advantage of being able to cut relatively wide boards. I found the saw to be pretty accurate and straight cutting right out of the box. I was pleased with the quality of the 60 tooth carbide blade and the smoothness of the cut. I read feedback from people saying that the saw did not eject sawdust very well into the sawdust bag. If you remove the bag and look into the sawdust outlet port on top (with the power off, of course) I saw that the casting of the blade guard in that area internal to the saw where the sawdust has to pass had metal ribs that stuck out into the discharge area and significant amounts of waste metal flashing from the casting process. I assume the protruding ribs inside the sawdust discharge port are some sort of safety arrangement. You can knock out the excess flashing with a screwdriver. Clearing the sawdust discharge path greatly improves the ability of the dust collection to work without clogging.
via sears.com
A clean and simple design that's worked exceptionally well on the few test cuts I've done so far. Needed hardly any setup and cut square and true right out of the box. And the laser was on the money. The sawdust collector, as others have noted, is virtually worthless. And you have to move the fence forward when cutting a rabbet. But, for the money, this is a great tool and worthy of the Craftsman name. Will be getting a workout soon as I help replace a friend's deck railings. If it lets me down, we'll let you know.
Westbrook, ME
via sears.com
dust collection leaves much to be desired bag is inefective. Even using shop vac attached to saw I have to vacumn my shop after using saw.
Ozone Park, NY
via sears.com
This is a very good product for the amount of money but I cannot get this saw to cut square. The problem is with the blade, it cuts okay once if the board is within 3 inches. Anything wider, one end is way off. I try replacing the blade and now looking to see if I can adjust the fence.
Edisto Island, SC
via sears.com
it is smooth and cuts great
Bayside, NY
via sears.com
i should have bought this years ago... if u need a miter saw- buy this one!!! the sliding feature allows u to cut boards up to 12' wide and at perfect 90 degrees.. no more uneven edges..
Bridgewater, VA
via sears.com
I bought the saw. On one side you get a square cut. From the other side, would not saw square cut. Fence molded crooked. Took saw back to Sears and they were nice to get me another one. Same problem with the other new saw. I had to attach shimmed boards to the fence and I finally got the saw to saw a square cut from both sides. This was a lot of trouble and time to spend on a new saw. I guess the saw would be OK for rough cuts where squareness was not an issue. Not recommended for a woodworking shop.
Houlton, ME
via sears.com
very easy to use. bought this for my son. i've had mine for 5 years and am extremely happy with the performance.
Adel, GA
via sears.com
The reviewer indicated they are affiliated with this product.
- Qualifying Orders $59 + SHIP FREE Offer ends 10-Jul-2013 See details.
- Use your Sears Card and Save! Extra 5% off Tool items Sold By Sears when you use your Sears Card. Offer ends 31-Dec-2013 See details.
- Online Only! Extra 10% off select tools Sold by Sears. Valid thru 5/22/13 8am CT. Offer ends 21-May-2013 See details.
