Share This Page Print

       00922290000-1
      Enlarge Image

      Craftsman  Dado Insert for 10 in. Belt Drive Table Saw

        Item#  00922290000 | Model#  22290
      Close

      Create a Review

       
       
       Rating 3.5 | 7 Reviews | Write a review
      $19.99
      Craftsman Club Price $17.99
      $19.99
      • Temporarily Unavailable
      I Own This Add to List
       

      Specifications & Dimensions

      Product Overview:
      Type: Inserts

      Overview

      Ratings & Reviews

      Special

      Projects

      Product Description

      For dadoing only. Fits saws: 12 in. direct drive (24250, 24501, 24502) and 10 in. [TT_BeltDrive] (22831, 22841, 22851, 221060, 226830, 249660, 290060, 290600, 290650, 298020.

      • No table saw is complete without high quality accessories
      • This combination dado/molding insert is an essential accessory for your table saw work

      This product is:
      • Available for Gift Wrap
      This product comes with:

      Added on July 26, 2010

       

      Overall, others give this:

      7 Reviews Write a review
      4 Reviewers (57.0%) would recommend this to a friend.
      Overall Rating Breakdown:
      5stars
      4stars
      (0)
      3stars
      2stars
      1stars

      Reviewers may have received a benefit, like a sweepstakes entry or rewards program points, in exchange for writing a review.
      Those benefits were not conditioned on the positive or negative content of the review.

      Most Helpful Reviews

      Praise1 found this helpful
      lkdmd
      Mar 30 , 2013
      Dado insert for 10" table saw
      Came as described/fits well our of the box/should do the job well.
      Criticism19 found this helpful
      Mr-Mac
      Jan 14 , 2011
      Dado insert leaves me wondering

      I bought this to put on my older Craftsman table saw so I could start cutting dadoe's (no, not Do Androids Dream of Electric Sheep) and rabbets.  I removed the old plate, slid this one into place and started to tighten the screw when I noticed that the screw hole was beveled too far to the center.  I returned that one hoping I just got one 'made on a Friday' but the next one was the same.

      I was able to overcome this issue by expanding the bevel on my drill press but the issue is quality control.  If this was built with a certain group of saws in mind then it cannot be labeld as a universal fit.  One thing to note is that it can be used without the screw installed, just don't lose the screw so when it's time to replace the insert you have it available.

       

      Mistasea

      Nokesville, VA

      Aug 5 , 2014
      via sears.com
      Overall
      Excellent Table Saw Accessory

      When making Dado Joints with a table saw, a Dado Joint insert is a necessity. This unit is easy to install, fits my Craftsman saw very well and was very reasonably priced. I would recommend this insert to other wood workers using a Craftsman 10 inch table saw.

      I would recommend this product to a friend.

      Helpful
      (1)
      Not Helpful
      (0)
      Flag this Review

      lkdmd

      Glastonbury, CT

      Mar 30 , 2013
      via sears.com
      Overall
      Dado insert for 10" table saw

      Came as described/fits well our of the box/should do the job well.

      I would recommend this product to a friend.

      Helpful
      (1)
      Not Helpful
      (0)
      Flag this Review

      wb42s

      Silsbee, TX

      Mar 18 , 2013
      via sears.com
      Overall
      Dado Insert

      Purchased this insert and had to overhaul it so it could be used. One of the adjusting screws was so tight I rounded off a allen wrench while getting it to move,the plate had a upward bow from front to rear (1/8th inch) , and the front retainer screw taper was smaller than the screw head. Craftsman quality is slipping away. Even with the overhaul it was a good purchase.

      I would recommend this product to a friend.

      Helpful
      (5)
      Not Helpful
      (0)
      Flag this Review

      sonnyos

      Quitman, TX

      Oct 30 , 2012
      via sears.com
      Overall
      Dado Insert for 10 in. Belt Drive Table Saw

      I would recommend this product to a friend.

      Helpful
      (1)
      Not Helpful
      (2)
      Flag this Review

      EMTD

      Jenison, MI

      Jun 6 , 2011
      via sears.com
      Overall
      dado insert did not fit the saw properly.

      Insert did not fit the saw properly. Had to grind one side smaller so it would fit down in the space properly for the screw to go in all the way. This is very disappointing since I bought it for a 10" Craftsman table saw.


      Helpful
      (5)
      Not Helpful
      (0)
      Flag this Review

      Mr-Mac

      Harrisburg, IL

      Jan 14 , 2011
      Overall
      Dado insert leaves me wondering

      I bought this to put on my older Craftsman table saw so I could start cutting dadoe's (no, not Do Androids Dream of Electric Sheep) and rabbets.  I removed the old plate, slid this one into place and started to tighten the screw when I noticed that the screw hole was beveled too far to the center.  I returned that one hoping I just got one 'made on a Friday' but the next one was the same.

      I was able to overcome this issue by expanding the bevel on my drill press but the issue is quality control.  If this was built with a certain group of saws in mind then it cannot be labeld as a universal fit.  One thing to note is that it can be used without the screw installed, just don't lose the screw so when it's time to replace the insert you have it available.


      Helpful
      (19)
      Not Helpful
      (0)
      Flag this Review

      Mr-Mac

      Saint Peters, MO

      Jun 2 , 2010
      via sears.com
      Overall
      Dado insert leaves me wondering

      I bought this to put on my older Craftsman table saw so I could start cutting dado's and rabbets.  I removed the old plate, slid this one into place and started to tighten the screw when I noticed that the screw hole was beveled too far to the center.  I returned that one hoping I just got one 'made on a Friday' but the next one was the same.

      I was able to overcome this issue by expanding the bevel on my drill press but the issue is quality control.  If this was built with a certain group of saws in mind then it cannot be labeld as a universal fit.  One thing to note is that it can be used without the screw installed, just don't lose the screw so when it's time to replace the insert you have it available.


      Helpful
      (8)
      Not Helpful
      (2)
      Flag this Review
      • Use your Sears Card and Save! Extra 5% off Tool items Sold By Sears when you use your Sears Card Offer ends   31-Dec-2015 See details.
      • Free shipping! Orders $59 or more Offer ends   31-Dec-2015 See details.
      • ONLINE ONLY! SYW Max Members get $5 back in points with a purchase of $25 or more in Tools. Offer ends   30-Apr-2015 See details.
      • Get Quarter ct tw Diamond Earrings for $19.99 with any storewide purchase of $19.99 or more! Offer ends   31-May-2015 See details.
      • Get Anvil or Bypass Pruner for $9.99 with any storewide purchase of $25 or more! Offer ends   31-May-2015 See details.

      close x