Specifications & Dimensions
|Assembly Required:||Assembly Required|
|Fits Brands/Models:||See product description for details|
|Mounting Hardware Included:||Yes|
|General Warranty:||1 year limited|
|Dimensions and Weight:|
|Item Weight (lbs.):||13|
|Vehicle Type:||Tractors only|
Ratings & Reviews
The Tractor Bumper Dual Bar Has Your Tractor Covered through Tough Tasks
Add both protection and style to the front end of your tractor and headlights, and prevent accidental damage with the super-strong Craftsman Dual Bar Tractor Bumper Constructed of one-piece, heavy-gauge steel tubing this dual bar bumper adds super-strong durability and protection to your Craftsman tractor. A rugged black, powder-coated finish adds scratch- and chip-resistant performance, as well as all-weather durability. When attached, the brush guard gives you easy access to your tractor – to open the tractor hood, you simply pull the lover to lower the bumper.
The Tractor Bumper Dual Barmounts easily to the tractor frame with included hardware. It fits all Craftsman and Husqvarna-brand front-engine tractors (except zero turn, rear engine rider and CTX series). The bumper can save you costly time and money with replacement expenses in excess of $100. One little fender bender, and you could be buying a new hood, headlights or grill due to damage – the brush guard adds the no-hassle protection you need to keep your tractor looking and working its best.
- The Craftsman Dual Bar Tractor Bumper guards your tractor as it works for you
- Comes with a 1-year limited warranty to protect your investment
- Weighing a super-light 13 lbs., it's extremely maneuverable and portable
- Fits all Craftsman and Husqvarna-brand front-engine tractors (except zero turn, rear engine rider and CTX series)
- Protects your tractor and front headlights from accidental damage
- Constructed of one-piece heavy-gauge steel tubing for a lifetime of durability
- Black powder-coated finish resists scratches and chips
- Mounts easily to tractor with hardware included
- Offers easy access to tractor
- Some minimal assembly required
Added on January 24, 2010
Overall, others give this:
Reviewers may have received a benefit, like a sweepstakes entry or rewards program points, in exchange for writing a review.
Those benefits were not conditioned on the positive or negative content of the review.
Most Helpful Reviews
This bar is built sturdy and provides protection against damage from low-impact front collisions. I also like the way it looks on the tractor. These are my assembly observations. First, for Craftsman model YT 4000 yard tractor, you do not need to remove the hood. Just raise it. You will need to remove the browning plate as described in the manual. Attach by placing washer on carriage bolt and inserting bolt through tractor frame from under neath tractor (bolt will point to outside) using first front bottom hole on tractor frame and 3rd hole on front of bumper bracket. Secure with whiznut. Do this for both sides and tighten. Now is tricky part. Place washer on bolt and insert into curved rear portion of bumper bracket and into top hole in rear of tractor frame with bolt pointing towards inside. If you follow manual and use same procedure as first bolts, you may have some difficulty holding bolt in place while you tighten whiznut do to limited work space. I found there is sufficient room on inside to use wrench (socket or standard) to tighten whiznut but very difficult to use pliers to hold bolt in that confined space. In other words, when you finish, you will have lower whiznut on outside of tractor frame and higher whiznut on inside of frame. This may not be an issue if you have small hands. Please note that in normal operation, the bumper becomes hot to the touch due to its proximity to engine components. Two of the end plugs became deformed and fell out, but this was no big deal for me. Over all, nice addition but assembly instructions leave quite a bit to be desired.
The bumper is of a good quality material, but it does take two folks to install. Plan on one hour installation time. Once installed, the bumper does add to the appearance of the lawn mower. If your in for looks, I recommend the purchase.
I didn't think it would be necessary but I was very wrong. It was greatly needed and it make the mower appear a little more stylish, so to speak. Glad I purchased one.
This bumper is easy to install and it wasn't necessary to remove the hood on my YT 3000 for install like the instructions stated and I found that the box came in handy since it is just the right height to hold up the bumper while you line up the bolt holes if you are doing it by yourself. I am very happy with it and it looks sharp!
Ballston Spa, NY
Installation went very well. The bumper is sturdy and should do a great job of protecting the front of the mower. I had one issue with the carrage bolts. They didn't allow the mounting brackets to come tight to the frame of the mower. I used the large washers provided to compensate for this. Other than that everything was slick.
Bought this bumper bar last year to help protect the front of my new YT4000. Installation was fairly easy & the bar looks good. My only complaint is the plastic end caps that go in each end of the horizontal tubes do not stay in. After about a month after installing the bar, 3 of the 4 end caps had come out, loosing 2 of the 3. When I attempted to get replacements, I was told they were not available. The salesman @ the Sears store where I bought the bar suggested I just returned the whole bar & get another one. I figured another bar would just do the same thing, so I elected to just keep the one I had. Now all 4 end tubes caps are gone. Sears sells parts for everything else, it would be nice if they would provide these end caps as a "part" available for sale as well. Or maybe these end caps should be pre-installed in the bar.