Specifications & Dimensions
|Item Weight (lbs.):||3.76|
|Tool Gauge Capacity:||18 ga.|
Ratings & Reviews
Drives 5 sizes of 18 ga. brad nails: 5/8, 3/4, 1, 1-3/16 and 1-1/4 in. at a rate of 30 per minute. Variable impact-force knob controls driving pressure. Long-life nylon magazine holds 100 nails.
- Available for Gift Wrap
Added on May 13, 2010
Overall, others give this:
Reviewers may have received a benefit, like a sweepstakes entry or rewards program points, in exchange for writing a review.
Those benefits were not conditioned on the positive or negative content of the review.
Most Helpful Reviews
San Jose, CA
I bought this to install baseboards (made of formed sawdust) in my home. First nail didn't even make it through the wood. I pulled it out with my fingers. Second went in, but not all the way. 1/4 of it was still sticking out. As for the third try...Nothing. I mean, it was as if there were no nails in the machine. I tried 3 more times before I gave up, repackaged it and returned it to the store. Don't waste your money on this item. Not worth the hassle.
Used it on 3 projects so far and no problem. Great for small projects. Saves a ton of time over trying to use a hammer and nail. Makes doing projects by myself so much easier.
The first one worked nicely for my project (approx. 200 brads), then later failed to sink brads...returned for new one under extended warranty. The new one has also failed during second project. Maybe the more expensive ones work....
I brought this because a friend used it in his house and liked it. I do a lot of wood working projects and have yet to be able to make a decision on the air compres nailer I want so I decided to try this out for $50. This nailer works well for small woodworking projects in medium to soft wood and putting up trim and molding only. Dont buy this if you plan on doing anything else with the tool. It is great when doing trim because you dont have to lug a air compressor with you everywhere. The downsides include the power and the consistency of the pressure. Lots of times the nail pushes the nail all the way in and then sometimes doesnt and I have to hammer them in. Overall it is a good purchase for $50 if you expectations are small projects. It can not handle a wide verity of projects
I brought this because a friend used it in his house and liked it. I do a lot of wood working projects and have yet to be able to make a decision on the air compres nailer I want so I decided to try this out for $50. This nailer works well for small woodworking projects in medium to soft wood and putting up trim and molding only.
Dont buy this if you plan on doing anything else with the tool. It is great when doing trim because you dont have to lug a air compressor with you everywhere. The downsides include the power and the consistency of the pressure. Lots of times the nail pushes the nail all the way in and then sometimes doesnt and I have to hammer them in. Overall it is a good purchase for $50 if you expectations are small projects. It can not handle a wide verity of projects
Lake Zurich, IL
I wish I would have read more reviews before buying this nailer. I figured it would be a good alternative rather than dragging out the compressor for a very small job I had. The purchase itself was a pain because the outside of the package doesn't indicate at all what nails will work in the nailer. I asked a Sears employee and they couldn't find any Crastman nails in the store that had this model listed on it. 18 gauge strip nails did worked. The unit itself didn't seem to have enough power to drive in an 1 1/4" nail through base shoe into drywall. I had to go back to nearly every nail I drove and pound it the rest of the way with a nail set. Additionally the power dial on the back is very sensitive, At one point I noticed the power got dialed way back because the cord brushed against the dial. The red bumper that you push into the wood to release the safety also popped off once. . . And I had all of these problems working with less than 10 feet of trim!
Salt Lake City, UT
Bought this to build a fireplace place mantel with hardwood (Alder). I wanted to get by on the cheap and avoid buying or renting compressors and air powered nailers. I opened a Sears charge account in order to save another $15 on the purchase price. I knew that the hardwood would be a challenge for the nailer, and so I had a hammer and nail setter handy as part of the job. It worked great. No jams, misfeeds, or misfires. It put the 1" brads in almost all of the way by setting it to full power. I did use the nail setter to finish off the brads that didn't quite make it all the way in. The nailer did not make any marks on the wood, as the nozzle protector worked well enough. .It did the job just fine, and if I had it to do all over, I would use this nailer again. It seems to be quite reliable and is a handy tool to have. No regrets.
Bluff City, TN
I bought this for small trim projects around the house, and after several done including building a new closet, it has yet to misfire or jamb. I'm using 1" Craftsman brads and have the power set to low, and it does fine with most trim. I ended up just throwing the little red safety cap away. It served no purpose other than to let the user know where not to put your fingers or hands when you pull the trigger. Really? Are people that stupid? Don't answer that! So, okay, it did split some oak trim a few times, but that can happen with any brad. That's not the nailer's fault at all. I also have a Craftsman compressor, and quite a few air tools, but can't imagine having to buy an air nailer unless I have to do some house framing. I got this brad nailer on sale on line which made it an even more desirable tool to have. So, I'm not saying it's the end all, be all of nailers, but for most small DIY projects should dojust fine. I plan to start framing pictures soon as I'm also into photography, and I'll really put this thing to the test, but so far, so good.
Cathedral City, CA
The nailer comes in a very nice case with extra brads included. The case keeps things together and is very easy to store and transport from one location to another. Brads are easy to load in the clip if you want to call it that. One thing is nice when you remove the clip the remaining brads do not fall out. The clip is easy to remove and replace. The hand works for either a left or right hand person. I am mainly left handed but it works well with either hand. My compresor can be adjusted for different pressures depending on the length of the brad or the hardness or thinkness of the material you are using. When the pressure is set right, the head of the brad is well below the surface to add putty to hide the head. However, in many cases, you don't have to use the filler because the hole is very difficult to see. But, if you like perfection then filler can be sued to really hide the brad. I have used the nailer quit a bit on a remodel project. It only misfired two or three times and those were my own fault and not the fault of the gun. I rate the gun as an excellent performer compared to the one I replaced with the craftsmen.
- Free shipping! Orders $59 or more Offer ends 05-Apr-2014 See details.
- Spend $199 in tools from Sears and enroll in the Tool of the Month - www.sears.com/toolofthemonth Offer ends 31-Dec-2014 See details.
- Use your Sears Card and Save! Extra 5% off Tool items Sold By Sears when you use your Sears Card. Offer ends 31-Dec-2014 See details.